extra wire on 02 harness? pic inside..

[White5.0]

http://i270.photobucket.com/albums/jj110/reb48/1217081559.jpg

this wire was just hangin there with my 02 plug not sure what its for? a ground maybe??

[97LaserRed]

hahah its for the flux capacitor!!:rofl: its above the tranny. thats why your car will be so damn fast!

on a serious note some cars have 4 wire o2 sensors some 3,2 even 1. im sure it just came out of the harness but i dont know fox bodys that well. I have no idea how ford did theres. find out what kind of o2 sensor you need and then youll be able to tell if its for the o2.

[wick]

For the left side? Its probably for the low oil sender.

[White5.0]

hahah its for the flux capacitor!!:rofl: its above the tranny. thats why your car will be so damn fast!

on a serious note some cars have 4 wire o2 sensors some 3,2 even 1. im sure it just came out of the harness but i dont know fox bodys that well. I have no idea how ford did theres. find out what kind of o2 sensor you need and then youll be able to tell if its for the o2.

haha im not driving a delorean lol

foxes have 3 wire o2's...and there is nowhere on the plug for it to go in...and the other plug only has 3 wires going to it

[jaa55]

if you give me til tomorrow morning i can tell you my engine bay is nothing but an empty hole right now

[White5.0]

For the left side? Its probably for the low oil sender.

yeah i think it is for the driver side and i think that may be it....im not using a low oil sender tho i just pluged the pan where the sender would go.

so if thats it i guess its nothing to worry about

[jaa55]

i think wick is right though i know the low oil sensor was in that harness, and it has a weird end on it that you have to pull a clip out of the oil pan to get it out

[97LaserRed]

For the left side? Its probably for the low oil sender.
i think its the passenger side?? but ya it could be the oil sender.

[White5.0]

if you give me til tomorrow morning i can tell you my engine bay is nothing but an empty hole right now

haha mine was once like that not too long ago....

yeah if you could check i would appreciate it:goodidea: i just thought it was weird since its just a bare end wire layin there

[White5.0]

i think its the passenger side?? but ya it could be the oil sender.

its the plug with the longer harness so i think its the driver side but not sure

[jaa55]

sensor is def the drivers side of the pan

[White5.0]

i think wick is right though i know the low oil sensor was in that harness, and it has a weird end on it that you have to pull a clip out of the oil pan to get it out

ohh i see i see.. well if its for that then i wont worry about it cause im not using one

[wick]

yeah i think it is for the driver side and i think that may be it....im not using a low oil sender tho i just pluged the pan where the sender would go.

so if thats it i guess its nothing to worry about


:goodidea: Mike is not in use either. Do yourself a favor and run them over the top of the bell housing. It cleans up some more of the engine bay.

[jaa55]

you know what give me 15 mins ill give you confirmation.......
running to the garage brb

[White5.0]

:goodidea: Mike is not in use either. Do yourself a favor and run them over the top of the bell housing. It cleans up some more of the engine bay.

thanks for the tip! ill try that out once i get my h pipe put on

[silvernotch]

We did an engine swap on a cousins fox and changed it to mass air.When we pulled the old engine I noticed that wire on his harness too never found out where it went

[Black87GT]

Its the oil level wire... no need for it.