help. 2011 5.0 shut off during driving

[Seer]

So loaded a new tune in today and took it out for some data logging.

Car drives perfectly, then it decides to shut off during WOT.

Limp it to the side of the road, and it will not turn over. SCT cannot connect to the pcm, cannot pull DTC's etc.

Gauges turn red, states check charging system and service advancetrac.

Pop hood, no leaks, no burning smells, nothing. Look at rear end same thing.

Disconnected battery, reconnected it, it is still doing it.

Turn key to on position you can hear fuel pump kick on and starter trying to work.

Think perhaps I can load a tune back into the car to reset things, SCT gives error 1027, wrong car blah blah, but that makes sense since it cannot communicate with the pcm.

[ModularMike]

Not enough NOSSSSSSSSSSSSSSSSSSSSSSS

[cam303]

I am guessing you have a fried ecm. It is a known issue with the 2011 up cars and loading aftermarket tunes.

[Seer]

it didnt fry loading the tune, it blanked out while driving.

I fixed it though, it was a popped fuse.

[Silverhatch]

it didnt fry loading the tune, it blanked out while driving.

I fixed it though, it was a popped fuse.
Found out what caused it to pop. Its probably gonna do it again.

[Seer]

Found out what caused it to pop. Its probably gonna do it again.

I'm about almost certain I figured out what did it.

[u1arunit]

I'm about almost certain I figured out what did it.

Care to share in case another person runs into the same problem?

[Seer]

Care to share in case another person runs into the same problem?

Fairly certain the bottle heater popped the fuse since I was drawing power from a particular key on fuse that was most likely in line with the pcm communications.

[wicked400ex]

So loaded a new tune in today and took it out for some data logging.

Car drives perfectly, then it decides to shut off during WOT.

Limp it to the side of the road, and it will not turn over. SCT cannot connect to the pcm, cannot pull DTC's etc.

Gauges turn red, states check charging system and service advancetrac.

Pop hood, no leaks, no burning smells, nothing. Look at rear end same thing.

Disconnected battery, reconnected it, it is still doing it.

Turn key to on position you can hear fuel pump kick on and starter trying to work.

Think perhaps I can load a tune back into the car to reset things, SCT gives error 1027, wrong car blah blah, but that makes sense since it cannot communicate with the pcm.

There is a TSB on No Start conditions:

INTERMITTENT NO START AND/OR ROUGH
RUNNING—BLOWN FUSE 13—DTC P0627
TSB 12-11-12
FORD:
2011-2013 Mustang
ISSUE
Some 2011-2013 Mustangs vehicles may exhibit an
intermittent drivability condition, crank/no start, a
blown fuse 13 in the battery junction box and may
have Diagnostic Trouble Code (DTC) P0627 stored
in the Powertrain Control Module (PCM).
ACTION
Follow the Service Procedure steps to correct the
condition.
SERVICE PROCEDURE
1.
Remove the rear seat cushion. Refer to
Workshop Manual (WSM), Section 501-10.
2.
Inspect the fuel pump module wire harness for
a chafing. Is chafing found? (Figure 1)
Figure 1 - Article 12-11-12
a.
No - this article does not apply. Refer to
Powertrain Control/Emissions Diagnosis
(PC/ED) manual for normal diagnosis.
b.
Yes - repair the wiring harness. Refer to the
Wiring Diagram (WD), Section 5.
3.
Route the harness so that it will lie in the
recess area of the rear seat when the seat
cushion is installed. (Figure 2)
Figure 2 - Article 12-11-12
4.
Install the rear seat cushion. Refer to WSM,
Section 201-10.
PART NUMBER PART NAME
F2UZ-14526-N 15 Amp Mini-fuse
WARRANTY STATUS:
Eligible Under Provisions Of
New Vehicle Limited
Warranty Coverage
Warranty/ESP coverage
limits/policies/prior approvals
are not altered by a TSB.
Warranty/ESP coverage
limits are determined by the
identified causal part and
verified using the OASIS
part coverage tool.
OPERATION DESCRIPTION TIME
121112A 2011-2013 Mustang:
Check DTCs, Inspect And
Repair Wire Harness (Do
Not Use With Any Other
Labor Operations)
0.8 Hr.
DEALER CODING
CONDITION
BASIC PART NO. CODE
14A005 30
NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do
the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper
vehicle service. The procedures should not be performed by “do-it-yourselfers”. Do not assume that a condition described affects your car or truck. Contact a
Ford or Lincoln dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine
Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article.The information in this Technical Service Bulletin (TSB) was
current at the time of printing. Ford Motor Company reserves the right to supercede this information with updates.The most recent information is available
through Ford Motor Company’s on-line technical resources.
Copyright ã 2012 Ford Motor Company Online Publication Date November 16, 2012
PAGE 1