Garage Sale

[mlowry1260]

I've been accumlating parts for far too long & need to clean house.

306/331/347 roller block, bored .030" & zero-decked, only needs a line-hone, $100

Holley Systemax II intake & 3/8" phenolic spacer, $350 SOLD
http://us.a2.yahoofs.com/users/439a6addzbddf0194/64e4re2/__sr_/4372re2.jpg?phoU5QFB8f6JJgM2

TFS 1.6 ratio 7/16" stud mount roller rockers, 7/16" studs, polylocks & guideplates
set of 16, with (2) extra rockers very good condition- $175

Holcomb Motorsports Mutha adj. upper upper control arms, NIB, $150
http://us.a2.yahoofs.com/users/439a6addzbddf0194/64e4re2/__sr_/d403re2.jpg?phoU5QFBDuGpNThn

Triple hook clutch quadrant & firewall cable adjuster $30 SOLD

3.55 FMS gear & Auburn differential, 28 spline ~25k miles $250

FMS X-303 cam, 224/224 duration, .542/.542" lift used $40

Ultradyne cam 218/218 dur., .525/.525" lift, 112 lca, nice street cam NIB $60

TFS TW .600" lift HR springs, 1500 miles, $25

FTI PS2 Springs 150 miles, .609" lift 145# seat $25

Valve spring retainers for above springs, $25

TFS 6.700" 5/16" diam x .083" wall chromemoly pushrods - $35

BBK 70MM TB & matching egr spacer, $65 SOLD

EEC-IV A3M ecu - $45 SOLD
Pro-M Race 80mm MAF & filter 30# cal '87-93 EEC-IV- $75 SOLD

Pro-M Race 80mm MAF & filter 36# s/c cal '96+ EEC-V - $75

EEC-IV Scan tool, Auto X-Ray OBD-I LCD display scanner, $65

Cobra Clutch & PP, 20K, lots of meat left on disk - $25

PSM Variflow electric fan controller, NIB, $25

Dynagear True Roller timing chain, p/n 78120, NIB, $25

* 76mm turbo - T4 exhaust flange, polished compressor housing, 4" inlet, 2.5" outlet, .96 AR hot side, 3.5" v-band exhaust, jet-hot coated turbine housing. Always run with an air filter. The turbo was purchased new and was been on the car for about 16 months. This was driven as a sunny weekend cruiser and racer at the track. I'd be surprised if the actual mileage on it is above 1000 miles. Ran a 9.32 @ 145 on a 377 windsor.
$850, turbo only. SOLD

http://saleen.v8mustang.com/pics/car/coupe/motor%20with%2076mm.jpg

Pics supplied upon request.

Mark

[Killercanary]

Mark, to run the PS2 springs, do the heads need cut? Will they work on AFR 165's?

Is the holley box stock?

[lib88stang]

what ecu was the A3M?
where are you located, interested in TB. Thanks

[mlowry1260]

Paul,

I would think they would work, they're a 1.46" OD spring from memory. I was a ble to run them in a stock TW spring cup.

The Holley is close to stock. I did some grinding to try & get the upper & lower to match up better. These things are big to start with. It's close to a 1262 gasket size at the heads.

What's the status on the yellow car? Did you ever solve your pedestal rocker issues?

lib88stang,

I'm in the Aliquippa area as stated in my profile. How about, where ya from?

Mark

[lib88stang]

I'm just south of pittsburgh in brownsville PA, also what was the ecu out of?

[mlowry1260]

It's been too long for me to remember where I got the ecu. I looked it up online and it's part of the family of A9L -- 88-93 Mustang includes A9L, A3M, A3M1, D3D1, X3Z, S0Z. I used it with a Tweecer.

[mlowry1260]

Will negotiate within reason.

[mlowry1260]

ttt

anyone?

[wick]

ttt

anyone?

I'll pm you in a bit. Gotta go to the eye doctors right now.

[Viper_ed]

What make is the Turbo?

[mlowry1260]

Ed,

it's a Garrett T-76.

Mark

[Viper_ed]

Thanks Mark! I'll be in touch.

[Rodeheaver's]

Is that turbo price for the entire kit, or for just the turbo? seems a little high for just a turbo, not being an ass, just asking a question..

[mlowry1260]

Is that turbo price for the entire kit, or for just the turbo? seems a little high for just a turbo, not being an ass, just asking a question..

The turbo cost over $1500 new and was jet-hot coated & polished. It's a turbo only. A kit with this turbo is around $4-5000.

Aren't used parts generally in the 50-60% of new? This thing is in great shape and I'll left anyone inspect it.

Price is negotiable within reason. This isn't some beat up high mile used junk off of the Corral.

[Viper_ed]

Ed,

it's a Garrett T-76.

Mark

Is it a Ball-Bearing Unit?

[Martin0660]

Mark - Stuff came today and is perfect. Thanks a lot, and bump for you.

Bob Myers

[Viper_ed]

Mark,

Do you have a part number for the turbo and does it have a waste gate on it?

[Viper_ed]

Thanks for the Turbo Mark! Great guy to deal with! :highfive: