any estimates on how much hp im making?

[PunisherStang]

hey guys im just curious on what kinda numbers i would be putting out on my 01 gt. you guys have been to dynos alot more than me so you guys hopefully know ballpark estimates. im looking to get a dyno tune also if anyone knows of some good places lettme know. i keep hearing sgs is a really good place for mustangs. so please give me your estimates and if you know any dyno places for a good dyno tune. i appreciate it.
Anyway heres my specs on my car: 01 gt block honed and bored .30 over, mahle forged pistons and rods, ported pi heads with new valves, crower stg 2 cams, crower valve springs i believe, compression is a little over 10:5:1, mac fenderwell intake, accufab 70mm tb an plenium,1 inch intake spacer, bbk u/d pullies, sct2 programmer, 4.10s, hooker longtubes, hooker offroad x pipe, slp loudmouth 1 catback, and royal purple oil lol. thankz:pinkthumb:

[Slow01GT]

With those mods you are prob in the 300-310rwhp range. As far as tuning goes, you def can't go wrong with SGS Automotive. Big Shot Dyno seems to be another popular place with a good rep.

[Troll]

I say 320-330RWHP with a good tune. There's Powerhouse in Erie also...http://www.powerhouse411.com/

[fastfox91]

With those mods you are prob in the 300-310rwhp range. As far as tuning goes, you def can't go wrong with SGS Automotive. Big Shot Dyno seems to be another popular place with a good rep.

agreed with what u have listed id say between 300 and 315 have u ever run the car at the track if so what et and mph and what does your car weight with u in it it gives a better bases to go off.

[PunisherStang]

never been to track, weight prolly in 3k range and i have beaten a 04 cobra with exhaust last summer on street. duno what they make stock but i had bout half a car on him he seemed like he could drive pretty good

[2001GTTT]

03/04's are like 375rwhp i believe....so either he wasnt too good a driver, your a really, really, good driver, or your car makes more power than you think. lol.

[PunisherStang]

i went to the dyno once with just full bolt ons and shortie headers and catted xpipe instead of longtubes and off road xpipe and my car made 264hp and 288tq this was at speed nation i only went because my friend knew the guy and got us a deal.

[2001GTTT]

did you spray when you beat the cobra?

[blkp42e]

http://www.crt-performance.com/

i went to CRT. Jeff is an awesome guy ti deal with and they are very reasonable. they also are very knowledgeable. I made 448hp on a street tune on a mustang dyno.

http://www.crt-performance.com/inthenews.htm

[PunisherStang]

no i didnt spray and my car is an automatic and i left it in drive.

[PunisherStang]

would the numbers you guys are estimating be on dyno or the crank?

[Cam99]

would the numbers you guys are estimating be on dyno or the crank?

Dyno ones are the only ones that matter LOL:goodidea:. I'm in the minority, but I don't like SGS, or at least when it was Kauffman's. If it's changed hands then I have no opinion on them. There are some vendors on here that do tuning also, might want to give them a shout.

[SonofaBish]

I don't do mustangs so i dont know crap about SGS, but shoot Wolfpack Speed a PM... he has a guy that does his tuning and he's very pleased with him....

[J-rod]

I don't do mustangs so i dont know crap about SGS, but shoot Wolfpack Speed a PM... he has a guy that does his tuning and he's very pleased with him....


he uses SGS i think....at least he just did on tylers car

[molnartr]

03/04's are like 375rwhp i believe....so either he wasnt too good a driver, your a really, really, good driver, or your car makes more power than you think. lol.

Stock 03 and 04 cobras were rated at 390 hp

[PunisherStang]

could i have a dyno freak lol j.k i think that irs was hurting him when we raced

[Pure Stock]

390 is Ford's FWHP rating for them. They are severly under-rated. The lowest RWHP I've come across was around 370 to the tires. Which translates into roughly 451 FWHP with an *assumed* 18% loss through the drivetrain.

The IRS makes it difficult to pour the steam to them, even in bone stock form.

[PunisherStang]

my car is an auto as well. isnt the hp rating lower than a 5 spd

[SonofaBish]

390 is Ford's FWHP rating for them. They are severly under-rated. The lowest RWHP I've come across was around 370 to the tires. Which translates into roughly 451 FWHP with an *assumed* 18% loss through the drivetrain.

The IRS makes it difficult to pour the steam to them, even in bone stock form.
agreed.... the 390 is sooo underrated.... i believe i've seen some do more than the 390 to the wheels dead stock..

[PunisherStang]

i never understand how the same car can make diffrent hp with the same mods, is their errors or does the machines get tired at the factorys?

[Pure Stock]

my car is an auto as well. isnt the hp rating lower than a 5 spd

Some automatics have more rotating weight compared to some manual trans. which will degrade RWHP output.

[Pure Stock]

i never understand how the same car can make diffrent hp with the same mods, is their errors or does the machines get tired at the factorys?

Differences in dyno's, production tolerences not being the same, something as minute as air pressure in drive tires, operating temps (engine oil temp, cylinder head temp, trans. temp, rear end temp), A/F ratio differences, the list goes on and on....

[Troll]

Differences in dyno's, production tolerences not being the same, something as minute as air pressure in drive tires, operating temps (engine oil temp, cylinder head temp, trans. temp, rear end temp), A/F ratio differences, the list goes on and on....

yeah, and when Ford or whoever says 390 or 260 or whatever... that is just an average of ten or so motors that they decided to test.

[2001GTTT]

Stock 03 and 04 cobras were rated at 390 hp
yes you are exactly right.....at the flywheel.

[LXguy88]

Bish, you speaking of Nate?

[PunisherStang]

so how much would i add percentage wise for the crank hp i know that the dyno numbers are the only one that matters but just was wondering? and troll is that how people come up with factory freak because they have more hp maybe from the ones they didnt test or etc etc.

[Pure Stock]

In post #7 you mention that combo generated 264 RWHP and 288 RWTQ with the automatic. I am going out on a limb here, so say the percentage of loss for your automatic is in the *range* of 20%-22%. We'll go with 22%.

264 RWHP converts to an approximate 338 FWHP

288 RWTQ coverts to an approximate 369 FWTQ

same numbers with 20% loss:

330 FWHP

360 FWTQ

I am not certain the percentage of loss attributed to the transmission in your application. Gives you an idea though.

[Troll]

and troll is that how people come up with factory freak because they have more hp maybe from the ones they didnt test or etc etc.
yes! If the 4.6 is "rated" at 260, sometimes you'll find one with 300 or 400hp! :yes: Just depends on the mood of the robot putting that motor together. :goodidea:

[PunisherStang]

damn thats crazy troll i hope i got a good robot on my block lol. and thanks pure stock for the percentage calculation. that was the dyno i did at speed nation with JUST bolt ons. so if im rougly 300 on just bolt ons on the dyno i should be way over the 330 estimates correct or did i just fall in the twilight zone of grasping this concept

[Pure Stock]

If it's making 300 to the tires, it's most likely yielding 375-385 to the flywheel. *IF* 20%-22% is an accurate representation of what the automatics soak up.

[PunisherStang]

so are those pretty good n/a numbers? i mean i know they are nice numbers but for my setup are they pretty stout numbers or should they be more or less. thanks for all your help pure stock, troll, and everyone else for your input an estimates

[Troll]

damn thats crazy troll i hope i got a good robot on my block lol.
ummm, I was kidding with you. what is your goal with this line of questioning/reasoning? do you just want to tell people your car makes 400hp or what? tell them whatever you want. :goodidea:

[Pure Stock]

300 + RWHP is stout from 284 cubic inches. I'm not well researched with 4.6L 2V combos. I'm kinda stuck in the "past" with the pushrod mills. Good luck with testing.

[fastfox91]

agreed not real good with the numbers of the 2 valve motors either, but a buddy of mine has a 5.4 in a 04 roush. it is a stock crank stock bore motor but does have dome pistons in it and compression is up there a little. also has cams not sure on the specs, it put down 368hp i believe which i thought was pertty good for it here is a video from when he had it out in cali remember even with out the hood lol this car is heavy http://www.youtube.com/watch?v=c37l3K04kTA still has some bugs being worked out with it

[PunisherStang]

troll i know you were kidding lol and im just trying to figure out a ball park of what my car will make on dyno and makes now. alot of people ask me what i make and i have nothing to say ijust say i made this on bolt ons so its prolly a big increase from that is what i say. i have seen 2v combos on the internet that i just find ridiculous and i have no idea how they make some numbers, i figured i would ask you guys since you have more dyno experience and have diffrent opinions. im just not looking forward to how much the dyno tune is gunna cost. and fastfox your buddies roush is very nice. does a hood not fit on it? i love the sheetmetal intake.:awsome:

[fastfox91]

no hes having a hard time finding one he likes and fitsm, that intake is crazy he paid like 1200 dollars for it, its a logan custom intake

[Troll]

decent info stolen from the corral on same question as yours:

A full bolt-on GT will make around 260rwhp with a good tune, give or take 10hp. The 10hp can easily be attributed to a better/worse tune, weather, or dyno type/calibration. Another thing, regardless of what people will BS you with. There is no such thing as a "factory freak". The cars make what they make. After that, it comes down to the driver to use that hp to it's fullest potential.

So, here it is. Stock mustang/bolt-on mustang Sticky facts;

1) A stock Mustang GT makes are 220-230rwhp.
2) Full bolt-on with a good tune. 260rwhp +/- 10hp
3) Full bolt-on with cams/tune - 280-300rwhp
4) Full bolt-on with cams/heads/tune - 300-340rwhp
5) Bone stock car with 100-150 shot or the equivalent boost from a supercharger, gears and sticky tires will make more power and be faster than all of the above!
6) Bolt-ons, besides gears and sticky tires are a waste of money, until you have heads/cams, nitrous, supercharger, or a turbo.


Until the motor is being restricted on the intake or exhaust side, you're not going to see any significant gains. If you're going for big power or speed, wasting $1000's on little bolt-ons to gain a maximum of 40hp, is just stupid. Once you're actually making some significant power over stock from either heads/cams or a power adder. Then you will actually see a decent gain from these bolt-ons. That is because the potential of the engine is now being restricted by the factory intake/exhaust, plenum, etc.

[SonofaBish]

Bish, you speaking of Nate?
where?

sorry, i'm sorta lost

[PunisherStang]

thats some nice info troll. thanks. troll did you get yours dyno tune or just handheld? an about that logan intake thats crazy on that price. i always liked the p51 intake manifold it dropped from the 1400 to like 700 i believe. i hear its better than the bullit intake dunno though.