low 9 sec combo must go

**biggb** · 08-19-2008, 04:13 AM

im selling all of the stuff that im going to replace for the new combo..prices are fairly firm but it never hurts to ask.....

410 stroker (2000 miles) 14 passes ------ 3000.00
74w block .040
eagle 4340 forged crank
eagle 4340 h beam rods
srp dished pistons ( 10.5.1 w/58c--11.1 w/ 54cc)
melling oil pump
comp hardened oil shaft
zero balnced
sfi balancer
sfi flexplate ( 157th c4 )
1/2 head studs
camshaft innovations .700 lift solid roller billet cam
comp billet timing chain
canton main girdle
canton windage tray
canton pick up
canton dip stick
canton 7qt oil pan

car ran 10.51@131 n/a and 9.50@145 on 150 shot there was way more in it, just wanting to step the game up a whole bunch...

tea 225 cnc high port heads 54cc ( 345/260 ish @.700 ) ----2100.00
with comp hi tech push rods ( 1 peice ) set up for solid roller
must use a 1262R intake gasket

pro systems 1000cfm hp race carb ---- 700.00

comp ultra gold race rockers 7/16 stud -----175.00

trickflow highport stud girdles ---100.00

hooker super comp 2inch headers ------350.00
3.5 inch collector 351 swap

edelbrock super vic 351 intake ----175.00

zex perimeter nitrous kit 100-300 hp -----450.00
w/ zex big noid purge, bottle heater, autometer 2 5/8 incar gauge ,blow down tube
wot switch for holley carb

aeromotive 13204 fuel press reg ---- 100.00
comes with regulator fittings

aeromotive a1000 w/ fuel filter ( 100 micron ) -----250.00

msd pro billet distributor ---- 200.00
mech advance 351 ( used with my super vic intake )

dedicated nitrous fuel system ---- 300.00
holley blue pump
holley 12-803 reg
fram fuel filter
6an earls pushlock
all an fittings bolt on and go

15x10 weld draglites ---- 350.00
4 lug
drilled for screws ( screws included)
with 28x12.50x15 et streets 65% tread

weld draglites 15x 3 1/2 ----250.00
with 90% front runners
4 lug

31 spline moser axles w/ long studs ----- 250.00
c clip eliminators
4 lug

31 spline trac loc 8.8 center recently refreshed ---- 100.00

msd digital 6 ignition ---- 150.00

msd blaster ss coil ----25.00

dynomax ultra flo welded mufflers 3inch ----75.00 pair

cervinis 4 inch cowl hood 87-93 ----- 350.00
painted flat black primer

autometer 2 5/8 fuel press gauge 0-15 psi ---- 30.00
i have 2 of these

art carr 1000 hp c4 FRESH ZERO MILES ----- 1000.00
hardened input shaft
pro billet trans brake
rev manual v.b
sfi jw bell
trans mount
alto red eagle clutches and steels
locking dipstick
deep aluminum pan
6 gear low drag planetary gear
fully rollerized
billet servo
plus much more...

ultimate converter concepts 9.5 c4 4200 converter ---- 400.00
fresh 2 months ago , 6 pass's
was redone then at ucc by lenny

3.73 motive gears --- 75.00

b&m ratchet shifter ----125.00
cable
brackets
polsihed cover plate
transbrake button shift knob

stock 87-93 hood red ----50.00
great condition

looking to buy another mustang for a driver/strip car to play with, so keep that in mind.... with a deposit i will meet within a reasonable distance on most of the bigger stuff, as i dont want to ship that stuff, please email ruthlessgsx@aol.com or call 814-207-3299
thanks

**biggb** · 08-20-2008, 04:34 AM

UPDATED ADD

im selling all of the stuff that im going to replace for the new combo..prices are fairly firm but it never hurts to ask.....

410 stroker (2000 miles) 14 passes ------ 3000.00
74w block .040
eagle 4340 forged crank
eagle 4340 h beam rods
srp dished pistons ( 10.5.1 w/58c--11.1 w/ 54cc)
melling oil pump
comp hardened oil shaft
zero balnced
sfi balancer
sfi flexplate ( 157th c4 )
1/2 head studs
camshaft innovations .700 lift solid roller billet cam
comp billet timing chain
canton main girdle
canton windage tray
canton pick up
canton dip stick
canton 7qt oil pan

car ran 10.51@131 n/a and 9.50@145 on 150 shot there was way more in it, just wanting to step the game up a whole bunch...

tea 225 cnc high port heads 54cc ( 345/260 ish @.700 ) --------2000.00
with comp hi tech push rods ( 1 peice ) set up for solid roller
must use a 1262R intake gasket

pro systems 1000cfm hp race carb ---- 650.00

comp ultra gold race rockers 7/16 stud -----150,00

trickflow highport stud girdles ---75.00

hooker super comp 2inch headers ------350.00
3.5 inch collector 351 swap

edelbrock super vic 351 intake ----175.00

msd pro billet distributor ---- 175.00
mech advance 351 ( used with my super vic intake )

dedicated nitrous fuel system ---- 300.00
holley blue pump
holley 12-803 reg
fram fuel filter
6an earls pushlock
all an fittings bolt on and go

15x10 weld draglites ---- 350.00
4 lug
drilled for screws ( screws included)
with 28x12.50x15 et streets 65% tread

weld draglites 15x 3 1/2 ----250.00
with 90% front runners
4 lug

31 spline moser axles w/ long studs ----- 250.00
c clip eliminators
4 lug

31 spline trac loc 8.8 center recently refreshed ---- 75.00

dynomax ultra flo welded mufflers 3inch ----75.00 pair

cervinis 4 inch cowl hood 87-93 ----- 300.00
painted flat black primer

autometer 2 5/8 fuel press gauge 0-15 psi ---- 30.00

art carr 1000 hp c4 FRESH ZERO MILES ----- 1000.00
hardened input shaft
pro billet trans brake
rev manual v.b
sfi jw bell
trans mount
alto red eagle clutches and steels
locking dipstick
deep aluminum pan
6 gear low drag planetary gear
fully rollerized
billet servo
plus much more...

ultimate converter concepts 9.5 c4 4200 converter ---- 400.00
fresh 2 months ago , 6 pass's
was redone then at ucc by lenny

3.73 motive gears --- 75.00

b&m ratchet shifter ----125.00
cable
brackets
polsihed cover plate
transbrake button shift knob

stock 87-93 hood red ----50.00
great condition

looking to buy another mustang for a driver/strip car to play with, so keep that in mind.... with a deposit i will meet within a reasonable distance on most of the bigger stuff, as i dont want to ship that stuff, please email ruthlessgsx@aol.com or call 814-207-3299

thanks

**Rio94gt** · 08-20-2008, 10:40 PM

PM sent

**biggb** · 08-23-2008, 04:08 AM

tttt

**biggb** · 08-23-2008, 04:15 AM

everything is back up for sale, here is a copy of the original add...thanks i had a deal pending but i cant wait that long for it to go through..

im selling all of the stuff that im going to replace for the new combo..prices are fairly firm but it never hurts to ask.....

410 stroker (2000 miles) 14 passes ------ 3000.00
74w block .040
eagle 4340 forged crank
eagle 4340 h beam rods
srp dished pistons ( 10.5.1 w/58c--11.1 w/ 54cc)
melling oil pump
comp hardened oil shaft
zero balnced
sfi balancer
sfi flexplate ( 157th c4 )
1/2 head studs
camshaft innovations .700 lift solid roller billet cam
comp billet timing chain
canton main girdle
canton windage tray
canton pick up
canton dip stick
canton 7qt oil pan

car ran 10.51@131 n/a and 9.50@145 on 150 shot there was way more in it, just wanting to step the game up a whole bunch...

tea 225 cnc high port heads 54cc ( 345/260 ish @.700 ) --------2000.00
with comp hi tech push rods ( 1 peice ) set up for solid roller
must use a 1262R intake gasket

pro systems 1000cfm hp race carb ---- 650.00

trickflow highport stud girdles ---75.00

hooker super comp 2inch headers ------350.00
3.5 inch collector 351 swap

edelbrock super vic 351 intake ----175.00

msd pro billet distributor ---- 175.00
mech advance 351 ( used with my super vic intake )

dedicated nitrous fuel system ---- 300.00
holley blue pump
holley 12-803 reg
fram fuel filter
6an earls pushlock
all an fittings bolt on and go

15x10 weld draglites ---- 350.00
4 lug
drilled for screws ( screws included)
with 28x12.50x15 et streets 65% tread

weld draglites 15x 3 1/2 ----250.00
with 90% front runners
4 lug

31 spline moser axles w/ long studs ----- 250.00
c clip eliminators
4 lug

31 spline trac loc 8.8 center recently refreshed ---- 75.00

dynomax ultra flo welded mufflers 3inch ----75.00 pair

autometer 2 5/8 fuel press gauge 0-15 psi ---- 30.00

art carr 1000 hp c4 FRESH ZERO MILES ----- 1000.00
hardened input shaft
pro billet trans brake
rev manual v.b
sfi jw bell
trans mount
alto red eagle clutches and steels
locking dipstick
deep aluminum pan
6 gear low drag planetary gear
fully rollerized
billet servo
plus much more...

ultimate converter concepts 9.5 c4 4200 converter ---- 400.00
fresh 2 months ago , 6 pass's
was redone then at ucc by lenny

3.73 motive gears --- 75.00

b&m ratchet shifter ----125.00
cable
brackets
polsihed cover plate
transbrake button shift knob

stock 87-93 hood red ----50.00
great condition

looking to buy another mustang for a driver/strip car to play with, so keep that in mind.... with a deposit i will meet within a reasonable distance on most of the bigger stuff, as i dont want to ship that stuff, please email ruthlessgsx@aol.com or call 814-207-3299 for pics and info...
thanks

p.s pics are available now just ask i had an unfortunate mishap with the transfer cable to my camera, thanks to my 10 yr old, who thought it was a grappling rope for his gi joe's

**HidalgoGT** · 08-23-2008, 12:10 PM

Lol, @ the 10 year old he was useing his brains though hehe.

**biggb** · 08-25-2008, 02:33 AM

everything is back up for sale, here is a copy of the original add i had somthing pending but it looks like im going to be waiting longer then i wanted so it all must go...

im selling all of the stuff that im going to replace for the new combo..prices are fairly firm but it never hurts to ask.....

410 stroker (2000 miles) 14 passes ------ 3000.00
74w block .040
eagle 4340 forged crank
eagle 4340 h beam rods
srp dished pistons ( 10.5.1 w/58c--11.1 w/ 54cc)
melling oil pump
comp hardened oil shaft
zero balnced
sfi balancer
sfi flexplate ( 157th c4 )
1/2 head studs
camshaft innovations .700 lift solid roller billet cam
crower link bar solid roller lifters
comp billet timing chain
canton main girdle
canton windage tray
canton pick up
canton dip stick
canton 7qt oil pan

car ran 10.51@131 n/a and 9.50@145 on 150 shot there was way more in it, just wanting to step the game up a whole bunch...

tea 225 cnc high port heads 54cc ( 345/260 ish @.700 ) --------2000.00
with comp hi tech push rods ( 1 peice ) set up for solid roller
must use a 1262R intake gasket

pro systems 1000cfm hp race carb ---- 600.00
comes with 6an carb fittings

trickflow highport stud girdles ---75.00

hooker super comp 2inch headers ------300.00
3.5 inch collector 351 swap

msd pro billet distributor ----150.00
mech advance 351 ( used with my super vic intake )

dedicated nitrous fuel system ---- 250.00
holley blue pump
holley 12-803 reg
fram fuel filter
6an earls pushlock
all an fittings bolt on and go

this can also be used for a motor fuel system, would connect to a carb log

15x10 weld draglites ---- 350.00
4 lug
drilled for screws ( screws included)
with 28x12.50x15 et streets 65% tread

15x10 weld draglites -----350.00
4 lug
with 28x10.50x15 et drag slicks 75% tread

weld draglites 15x 3 1/2 ----250.00
with 90% front runners
4 lug

31 spline moser axles w/ long studs ----- 250.00
c clip eliminators
4 lug

31 spline trac loc 8.8 center recently refreshed ---- 75.00

dynomax ultra flo welded mufflers 3inch ----75.00 pair

autometer 2 5/8 fuel press gauge 0-15 psi ---- 30.00

art carr 1000 hp c4 FRESH ZERO MILES ----- 1000.00
hardened input shaft
pro billet trans brake
rev manual v.b
sfi jw bell
trans mount
alto red eagle clutches and steels
locking dipstick
deep aluminum pan
6 gear low drag planetary gear
fully rollerized
billet servo
plus much more...

ultimate converter concepts 9.5 c4 4200 converter ---- 400.00
fresh 2 months ago , 6 pass's
was redone then at ucc by lenny

3.73 motive gears --- 75.00

b&m ratchet shifter ----125.00
cable
brackets
polsihed cover plate
transbrake button shift knob

ford racing polished tall valve covers ---50.00

stock 87-93 hood red ----50.00
great condition

looking to buy another mustang for a driver/strip car to play with, so keep that in mind.... with a deposit i will meet within a reasonable distance on most of the bigger stuff, as i dont want to ship that stuff, please email ruthlessgsx@aol.com or call 814-207-3299 for pics and info...

thanks

p.s pics are available now just ask i had an unfortunate mishap with the transfer cable to my camera, thanks to my 10 yr old, who thought it was a grappling rope for his gi joe's