Just wanna show my car off.

[slimvdub]

Hello I am on hear all the time look and getting info selling and buying parts. I just thought I would show ever one what I have and been working on.

Its not a mustang but it is close. It is a 1986 mazda rx7 gxl with 4 pot calipers and all wheel disk independent rear suspension with 4.10 gears. Az car no rust.

Ok now the reason it is close to a mustang. I have a 5.0 H.O carbed engine with a 204/214 duration cam flat top pistons Summit intake and eldebrock 600cfm carb no clutch fan ac elimanator underdrive pullies, and GM hei ignition set up. The exhaust is custom stainless with an x pipe and flow masters made by Jeff at 1st try.

Ford T5 with ram street and strip clutch kit switched to hydrulic clutch with wilwood clutch master and pull style slave cylinder custom drive shaft.

Engine and tranny installed using grannys speed shop engine and tranny kit. worked real well. Best part about the car is that everything works all factory gauges with a little work and some soilder and a 1000ohm resisiter and speedo buy using a mustang speedo cable and a speedo gear from steeda for using 4.10 gears its 3 mph off , stock looking interior

I havent taking it to the track yet I hope for 14's in the 1/4 i am going to go this summer a few times. Hope you guys like it.

[John4cam]

Nice!! Let us know how it runs!!

[White5.0]

thats an awesome car i love seeing 5.0's in rx-7's/miata's i wanna do that swap one day...

i think you'll have no problem getting 14's youll probably do way better than that those cars are light!

[Hawkeye]

Thats cool.....nice job!

[AdamantiumSilvr]

That's awesome!!! I'm all about uniqueness and bein different, for sure!! Originality! Never seen that combo before. Luv ta check it out in real life. Let us know when your taken it out in about.

[slimvdub]

yeah i will let people know when i go it should be fun. You have no idea how many honda kids try to screw with me. And it made me realize some people know nothing about cars. I was at the sheetz in moon getting gas and checking my oil when some one came over after getting out of his wrx with an exhaust and stuff and looked at my car and asked " Is there anything done to it" I just laughed and said no lol

[2001GTTT]

thats a really cool idea man, nice work!

[Shorty429]

thats awesome! i'm a huge fan of rx-7's! looks great too

[97LaserRed]

thats badass! i think youll def be 14. those cars are so light its not even funny!

[SoLow]

BAD ASS....looks great man, and as already stated 14's def should be a prob being as light as them are..

looks like Jeff did a Awesome job as usual on ur exhaust too !

[yeahloh95]

i had a mazda once with a 306 it was a b2000 though and was alot of fun . nice ride you have there.

[Rodeheaver's]

thats pretty cool, there is one of those running around here with a chevy mill in it...

[slimvdub]

This spring I am going to go back to fuel injection too. I have a 96 explorer upper and lower intake all the sensors for mass air the Distrubutor. Pretty much every thing except the fuel injectors rails and pump. I dont know if I would be getting any more power from all this I just like how fuel injection works better. Plus after doing this I could space the subframe down like 1/2 inch and fit it under a stock hood all about being sleeper. What do you guys think good idea or bad idea?

[billyNOTnice]

nice project... i've done the same thing with a chevy 350 :)

[MBH]

That's awesome! Guarantee you'll confuse a lot of people with the exhaust note :)

[SonofaBish]

Cool man! I see a lot of people stuffing LS1's in those cars...

Will definitely make people look twice

[scott5]

looks good