Any local flow benches?

**somethingclever** · 03-23-2009, 02:55 PM

Was wondering if anyone knew of any local engine shops with a flow bench.

**Sonic03snake** · 03-23-2009, 03:35 PM

I believe Mark @ The Motorworks in Greensburg has one.

Originally Posted by somethingclever

Was wondering if anyone knew of any local engine shops with a flow bench.

**Rodeheaver's** · 03-23-2009, 03:54 PM

there is 3 down my way, give me a call if you are interested in any of them..

**George** · 03-23-2009, 06:34 PM

flowbenches r benchracing material.

**Viper_ed** · 03-23-2009, 06:52 PM

Originally Posted by George

flowbenches r benchracing material.

Not if you're using them to properly port heads.

**somethingclever** · 03-23-2009, 09:30 PM

Originally Posted by George

flowbenches r benchracing material.

George if you knew me you would have already known that's the ONLY racing I do.

Just incase you're wondering I'm going to get flow numbers @ .900" lift and put a cam in the engine to lift it .420" @ the valve. That's just how I roll.

Thanks guys...I really didn't expect to hear about any in the area....good to know.

**George** · 03-23-2009, 10:20 PM

Originally Posted by somethingclever

George if you knew me you would have already known that's the ONLY racing I do.

Just incase you're wondering I'm going to get flow numbers @ .900" lift and put a cam in the engine to lift it .420" @ the valve. That's just how I roll.

Thanks guys...I really didn't expect to hear about any in the area....good to know.

It doesn't matter if you lift the valve off the seat a half of a foot, what matters is e.t. Got e.t.???

**Martin0660** · 03-23-2009, 10:29 PM

Originally Posted by somethingclever

George if you knew me you would have already known that's the ONLY racing I do. .

bwhahahahahahahaha.... actually, I have seen you leave above idle before :D

Originally Posted by somethingclever

Just incase you're wondering I'm going to get flow numbers @ .900" lift and put a cam in the engine to lift it .420" @ the valve. That's just how I roll.

working on the 2.3 combo is see

**somethingclever** · 03-23-2009, 10:38 PM

Originally Posted by George

Got e.t.???

Absolutely......

Positively........

No.

But thanks for your input to this thread. It's much appreciated.

**somethingclever** · 03-23-2009, 10:40 PM

Originally Posted by Martin0660

bwhahahahahahahaha.... actually, I have seen you leave above idle before :D
:

garunteed you saw one of two things:

1.) Tires spinning

2.) Clutch slipping

:)

**CobraII** · 03-24-2009, 04:54 PM

I'm also pretty sure Mark at The Motorworks has one also... I'll see if I can confirm that through one of the crew, if they don't see the post.

I also think Gregg Dahl at Gregg's Machine Service/GMS in Uniontown has one.

**CobraII** · 03-25-2009, 12:56 PM

Confirmed it with Christine (ie, christine57, or Mrs. Brewer :D), Motorworks does indeed have a flow bench. Call for pricing.

1020 Broad Street
Greensburg PA 15601

724-832-9744

**somethingclever** · 03-25-2009, 01:27 PM

Thanks a bunch....going to be a couple weeks before the machine shop is done setting up the heads for my new valves/springs/....etc.

**Killercanary** · 03-25-2009, 01:32 PM

I know Ken Frisco (sp) used to have one in his shop out near Greensburg as well. He's off of Rt 119 near Rizzo's restraunt. Its been years since I've spoken with him so I don't even know if he still has it or his shop anymore though. He's a regular at PRP though so someone here should be able to confirm if he is still out that way.