I need the 4 bolt adapter that bolts to the MAF like the one shown in this kit....
I need the 4 bolt adapter that bolts to the MAF like the one shown in this kit....
03 Torch Red Anni. Ed. Cobra
11 Grabber Blue 5.0, 3D500 spoiler, CS valance, GT premium, interior upgrade package, Brembos, MT-82 and Whipple powered SOLD
01 cobra: traded
93 LX Modular 4v swap
Sean Hyland Motorsport forged rotating assembly, Teksid block, 01 cobra heads, cams and intake SOLD
I have one from a Vortech kit that mounts up in the fender well of a 94/95 car. It gets you lots more room. Not sure if it will work on the 93 car.
03 Cobra redfire vert - 466 rwhp / 456 rwtq
Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs
Like this one:Originally Posted by 95DropTop
03 Cobra redfire vert - 466 rwhp / 456 rwtq
Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs
that will work, just cut off the bracket, or you may be able to use it..
2015 A6 Mustang GT that so far has gone 9.48@147 but still the fastest prochargerd S550 in the world aside from Tim Essick's!
www.Rodeheavershotrod.com
Thats it, i want to go back to 19# injectors and im planning on using a Mark VIII MAF
what do you want for it?
03 Torch Red Anni. Ed. Cobra
11 Grabber Blue 5.0, 3D500 spoiler, CS valance, GT premium, interior upgrade package, Brembos, MT-82 and Whipple powered SOLD
01 cobra: traded
93 LX Modular 4v swap
Sean Hyland Motorsport forged rotating assembly, Teksid block, 01 cobra heads, cams and intake SOLD
10.00 + around $5.00 if you want me to ship it to you. I think the cost is $4.40 UPS ground. So $15 will cover it if shipped. Or, of course, you can pick it up.
Let me know if you want it.
Thanks, Vince.
03 Cobra redfire vert - 466 rwhp / 456 rwtq
Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs
Ok, I dug the bracket up this AM and now realize that it is a slight bit different than the stock pic that I sent you.
Here is an actual photo.
This one mounts in the fender on a slightly different bracket and has a bung for the Air Temp Sensor in it. You may already have a provision for the Air Temp Sensor in your CAI or elsewhere.
Like I said, if you want to mount this thing in your fender and get the MAF and filter tucked away in there, it is a great solution. If you are going to put the stuff where it normally goes, then this may not be for you.
Let me know if you still want it and I will send it to you today.
03 Cobra redfire vert - 466 rwhp / 456 rwtq
Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs
hmm im not sure that will work for me.......i think it needs to be pretty shallow in the hole im going to put it in, i want to connect the mark 8 MAF to my stock air box with the factory connector
03 Torch Red Anni. Ed. Cobra
11 Grabber Blue 5.0, 3D500 spoiler, CS valance, GT premium, interior upgrade package, Brembos, MT-82 and Whipple powered SOLD
01 cobra: traded
93 LX Modular 4v swap
Sean Hyland Motorsport forged rotating assembly, Teksid block, 01 cobra heads, cams and intake SOLD
Yeah, sorry. I didn't have it with me and forgot that it had that built-in bung. Good luck finding what you need!
03 Cobra redfire vert - 466 rwhp / 456 rwtq
Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs
thanks for the response and pics!
I may try to get it off you if i dont come up with anything
03 Torch Red Anni. Ed. Cobra
11 Grabber Blue 5.0, 3D500 spoiler, CS valance, GT premium, interior upgrade package, Brembos, MT-82 and Whipple powered SOLD
01 cobra: traded
93 LX Modular 4v swap
Sean Hyland Motorsport forged rotating assembly, Teksid block, 01 cobra heads, cams and intake SOLD
Posting Permissions
Reply With Quote
Bookmarks