Results 1 to 3 of 3

Thread: FS: 2 Chrysler Remote Fobs

  1. #1
    Senior Member 95DropTop's Avatar
    Join Date
    May 2007
    Location
    Gibsonia, PA
    Posts
    323

    FS: 2 Chrysler Remote Fobs

    Hi.

    I have two brand new OEM keyfobs for Chrysler.

    These were bought for my wifes 2002 Voyager that didn't have keyless entry from the factory. I never got around to getting the necessary wiring harness installed and these things programmed. We no longer have the van.

    These work on a lot of different Chrysler vehicles. Pretty sure on Dakotas, Rams, Durangos, etc., too.
    Look up the part number to see if it fits your vehicle.

    $20.00 for both shipped.

    Daimler Chrysler
    P/N: 04686481AC
    FCC ID: GQ43VT17T
    CANADA: 1470 102 1294


    The photo is a stock photo but they look like this.
    Attached Images Attached Images
    Last edited by 95DropTop; 11-07-2010 at 11:00 PM. Reason: added one note about fitting more vehicles
    03 Cobra redfire vert - 466 rwhp / 456 rwtq

    Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs

  2. #2
    Senior Member ruger77's Avatar
    Join Date
    Mar 2009
    Location
    Greensboro, PA
    Posts
    133
    They will need reprogrammed for another vehicle right?
    • 1988 Mustang GT - 5spd. - 12.09@117 Procharger just added! Times???
    • 2005 Dodge Ram Hemi - 13.57@ 100.9mph(75shot)
    • 2006 Eclipse GT - 6spd. - wife's - 14.09@ 97.9mph (CAI only)
    • 2010 Focus SES - wife's - 37.8mpg!

  3. #3
    Senior Member 95DropTop's Avatar
    Join Date
    May 2007
    Location
    Gibsonia, PA
    Posts
    323
    Sorry for the late reply.

    These have never been programmed at all. They are brand new. I think that it depends on the vehicle. Some vehicles allow you to do it yourself and some you have to take it to a dealer to get it done.

    The dealers typically charge their hourly rate so if they charge 90.00/hr and it takes 30 mins, then you pay 45.00/hr. That is what the dealer told me a while back when I called them. I never got it done, though. Sold the car.
    03 Cobra redfire vert - 466 rwhp / 456 rwtq

    Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs

Similar Threads

  1. Jeep pickup kit from Chrysler
    By Ares in forum The Bar
    Replies: 1
    Last Post: 07-21-2011, 12:17 AM
  2. Need Dodge/Chrysler/Jeep parts?
    By pRojekt02GT in forum The Bar
    Replies: 0
    Last Post: 08-27-2010, 08:41 PM
  3. Replies: 19
    Last Post: 05-16-2009, 02:52 AM
  4. Chrysler selling viper
    By SUPERDUTY in forum The Bar
    Replies: 17
    Last Post: 09-13-2008, 09:45 PM
  5. Chrysler and ford joint adventure
    By Jivepepper in forum The Bar
    Replies: 10
    Last Post: 07-12-2008, 02:01 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •