Results 1 to 11 of 11

Thread: Potential Trade 3.73 for 3.27 rear end

  1. #1
    Senior Member 95DropTop's Avatar
    Join Date
    May 2007
    Location
    Gibsonia, PA
    Posts
    323

    Potential Trade 3.73 for 3.27 rear end

    I have a very clean stock 28 spline 8.8 in my supercharged 95 Mustang GT that has 3.73 gears in it.

    The rear end was done by Mike at Woflpack Speed about 2000 miles ago.

    Frankly, the 3.73 gears are a bit too much for me. First gear is relatively useless and it is a convertible and I drive it on the highway a lot. I am looking to knock the RPMs down (and the drone of the exhaust) a bit when going 70 MPH on the highway.

    My rear end has 65,000 original miles on it. Car was never raced and was never in slicks. Fresh gear job with good install kit and shims with Royal Purple 2000 miles back or so.

    Looking for a nice rear end to swap in with good mileage and with 3.27 gears in it.

    Anyone got anything for trade?
    Last edited by 95DropTop; 10-30-2011 at 12:29 PM. Reason: Typo on axel spline count that I just noticed.
    03 Cobra redfire vert - 466 rwhp / 456 rwtq

    Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs

  2. #2
    Tripedalist yeahloh95's Avatar
    Join Date
    Aug 2006
    Location
    Everett, Pa
    Posts
    5,065
    i have a set of used 3.27's i'll sell you then you can just swap them into your housing
    Troy
    95 gt 11.3 @ 126
    68 f100 SB soon to be coyote powered
    12 GT 6m cobra jet powered 11.4 @124
    90 lx supercharged 440 rwhp on 8 lbs
    17 f150 crew cab coyote powered

    PEOPLE HAVE MORE FUN THAN ANYONE

  3. #3
    Senior Member 01cobra's Avatar
    Join Date
    Sep 2007
    Posts
    131
    Have a set of 3.27 out of a 2001 cobra with 2158 mi. Will trade, i'm just in Butler, not far from you. Let me know! Fran

  4. #4
    Nothing clever to say.... jaa55's Avatar
    Join Date
    Sep 2007
    Location
    Dayton PA
    Posts
    3,795
    I also have a set of 3.27s out of an 01 cobra
    03 Torch Red Anni. Ed. Cobra

    11 Grabber Blue 5.0, 3D500 spoiler, CS valance, GT premium, interior upgrade package, Brembos, MT-82 and Whipple powered SOLD

    01 cobra: traded

    93 LX Modular 4v swap
    Sean Hyland Motorsport forged rotating assembly, Teksid block, 01 cobra heads, cams and intake SOLD

  5. #5
    25 in the 1/4 SlowSix's Avatar
    Join Date
    Nov 2010
    Location
    Greensburg
    Posts
    1,309
    Someone is selling a 94-98 rear with 3.27s in it in the for sale section. I would probably take your rear off your hands if you bought that.


    Just a little 500 whp V6

  6. #6
    Senior Member blizzard's Avatar
    Join Date
    Mar 2008
    Location
    Castle Shannon
    Posts
    1,276
    oh snap, i better get in line eh?

    but if everybodys trading rears,, i have a 99gt rear with 3.27s and 18k "new", ???

  7. #7
    25 in the 1/4 SlowSix's Avatar
    Join Date
    Nov 2010
    Location
    Greensburg
    Posts
    1,309
    Quote Originally Posted by blizzard View Post
    oh snap, i better get in line eh?

    but if everybodys trading rears,, i have a 99gt rear with 3.27s and 18k "new", ???
    Pm'd
    Why could I not find a rear before, and now they're everywhere?


    Just a little 500 whp V6

  8. #8
    Senior Member 95DropTop's Avatar
    Join Date
    May 2007
    Location
    Gibsonia, PA
    Posts
    323
    Quote Originally Posted by blizzard View Post
    oh snap, i better get in line eh?

    but if everybodys trading rears,, i have a 99gt rear with 3.27s and 18k "new", ???
    Do you want to trade or are you looking to sell yours?
    03 Cobra redfire vert - 466 rwhp / 456 rwtq

    Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs

  9. #9
    Senior Member
    Join Date
    Jun 2010
    Location
    volant, pa 1 hour 10 minutes to summit
    Posts
    576
    if u could live with 3.55s i have a set u can have for the ride
    6.4 litre fox and its all ford

  10. #10
    Senior Member 95DropTop's Avatar
    Join Date
    May 2007
    Location
    Gibsonia, PA
    Posts
    323
    Quote Originally Posted by cemnt guy View Post
    if u could live with 3.55s i have a set u can have for the ride
    PM sent.
    03 Cobra redfire vert - 466 rwhp / 456 rwtq

    Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs

  11. #11
    Senior Member 95DropTop's Avatar
    Join Date
    May 2007
    Location
    Gibsonia, PA
    Posts
    323
    Thank you, Cemnt Guy, for the gears!

    I will get these installed and I should be good to go.

    Much appreciated!
    03 Cobra redfire vert - 466 rwhp / 456 rwtq

    Mods: Bassani Mid Length Headers, X Pipe and Cat Back, Accufab Big Oval Throttle Body And Polished Inlet Plenium, 2.95 Reichard Ultra Grip Pulley, MotoBlue Auxiliary Idler Pulley Kit, LFP Double Pass Heat Exchanger, K&N FIPK, C&L intake Pipe, 3.73 Gears, MGW Shifter, Spec stage 2 clutch, Fidanza aluminum flywheel, MotoBlue Hard Launch Bar, Full Tilt Boogie Racing kit and H&R Race springs

Similar Threads

  1. 08 7.5 rear end
    By scorpio333 in forum Ford Vehicles
    Replies: 6
    Last Post: 06-07-2017, 10:33 AM
  2. 8.8 rear end.
    By NateSVT in forum Ford Parts
    Replies: 0
    Last Post: 08-01-2011, 09:51 AM
  3. Need help! Rear end
    By Darren in forum Wolfpack Speed
    Replies: 1
    Last Post: 01-24-2011, 03:44 PM
  4. Rear end help!
    By Darren in forum General Tech
    Replies: 2
    Last Post: 01-23-2011, 03:16 PM
  5. rear end?
    By 94svtcobra in forum General Tech
    Replies: 5
    Last Post: 07-13-2008, 07:55 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •