Page 1 of 2 12 LastLast
Results 1 to 20 of 22

Thread: New Cobra Pron From Old Member

  1. #1
    Chief MarcInJapan's Avatar
    Join Date
    Mar 2009
    Location
    Syracuse, UT
    Posts
    34

    New Cobra Pron From Old Member

    Finally settled in here in Utah after being overseas for 10 years. I am stationed at Hill AFB here. Bought a house with a 3-car garage which I am enjoying. I have 2.5 years left in the service before I retire at 30 years.

    Finally got all the goodies installed on the cobra.

    Here are the goodies:

    MOTOR
    2.9 Whipple Supercharger (Polished)
    Lethal Performance 1000HP Fuel System--3 Fuel Hats/fuel lines, Zone 5, electronics, etc.
    Semens Deka 80 LB High Impedance Injectors
    Fore Precision Works Polished Fuel Rails
    AFCO Pro Series Dual Pass Heat Exchanger
    SCT Xcal3 Programmer/Handheld Tuner
    PFAB Radiator Expansion Tank (Polished by Mirror Finish Polishing)
    PFAB Supercharger Tank (Polished by Mirror Finish Polishing)
    EGR Delete Kit
    Reische 170 Degree Thermostat
    Even Flow Generation 2 Head Cooling Mod
    JLT Oil Separator
    JLT Carbon Fiber CAI
    SCT BA-3000 MAF (Polished)
    MotoBlu Idler Pulley (Polished)
    Accufab Single Blade Throttle Body and Intake Plenum (Polished)
    Motoblue Idler Pulley
    Reichard Racing 3.5 Racing Pulley (Polished by Mirror Finish Polishing)
    Polished 3.0 Pulley
    NGK Spark Plugs

    CLUTCH
    Mcleod RXT 26 Spline Clutch
    Mcleod Lightened Steel Flywheel
    D&D 26-Spline Input Shaft
    Lethal Performance T-56 Throwout Bearing Retainer Sleeve
    Fiore Micro-Click Firewall Adjuster & Quadrant
    LDC Chicago Clutch Freeplay Correction Kit
    Ford Racing Roller Pilot Bearing
    Ford Racing Heavy Duty Throw Out Bearing

    EXHAUST
    Bassani X Pipe without Cats
    Flowmaster 40s Cat-Back Exhaust

    Purchased and waiting to be installed: Stainless Steel Magnaflow Exhaust System

    SUSPENSION
    Maximum MotorSports Chrome Caster Camber Plates
    Hans Full Length Subframe Connectors
    Steeda Bump-Steer Kit
    Summit Racing Driveshaft Loop
    Fore Precision Works Aluminum IRS Differential Cover
    Eibach Pro Lowering Springs

    INTERIOR
    AeroForce Dual Guages & Wideband
    Speed Hut Pillar Pod
    Custom Embroidered Headrests
    Raptor Shiftlight
    Pro 5.0 Shifter for Tremmec T56
    F'n Fast Shift Knob

    EXTERIOR
    Cobra Grill Emblem
    Redline Hood Shocks
    Tinted Rear Taillights & Rear Side Markers
    Tinted Windows
    Cobra Billet Exterior Gas Lid
    MGP Caliper Covers
    Billet Oil and Radiator Caps
    UPR Chrome Oil Dip Stick
    UPR Chrome Battery Hold-Down
    Fore Precision Works Hood Vents
    Sequential Tail Lights

    Next Purchase: *American Racing 1 3/4 Longtube Headers w/their X-pipe.

    Motor shots:




    Rear Shot:



    Side Shots:




    Couple Shots Of The Cobra & The 92 Notch I own as well.




    Here is the Dyno Sheet:



    Here is the dyno video:

    [ame=http://www.youtube.com/watch?v=4I9slgMGBq4&feature=player_embedded]Marc Hill pump gas dyno vid.AVI - YouTube[/ame]

    My tuner said I should hit near 650 HP on 91 Octane and break the 700HP barrier on race gas with the new headers and new tune.

    Take care and thanks for looking!

    622 HP/525 Torque On Pump Gas
    UnitedStangs.com
    MustangMafia.com

  2. #2
    Chief MarcInJapan's Avatar
    Join Date
    Mar 2009
    Location
    Syracuse, UT
    Posts
    34
    MODS: I am no longer stationed in Japan. Can I get a name change?

    I would like "Marc" if that is no problem. Doesn't seem to be taken right now.

    622 HP/525 Torque On Pump Gas
    UnitedStangs.com
    MustangMafia.com

  3. #3
    More Power to Come! Stroked03Cobra's Avatar
    Join Date
    Oct 2009
    Location
    Kittanning/Butler
    Posts
    1,055
    Gotta love the CO! Great lookin term!
    2003 Sonic Blue SVT Cobra - 711 RWHP @ 671 TQ @17psi. Kenne Bell 2.8, FRPP Modular Boss 5.0 block, Big Bore 324ci, with full stroker kit, JDM Stage 3 Heads, Custom Grind Cams and alot more. 4,900 original miles..... Currently at Street Lethal Performance for a makeover!

    1997 Mustang GT - 5 speed, 34k original miles

    1968 Fairlane GT - 302ci Hurst 4 Speed

    1999 Crown Vic - P71 Clone, JLT CAI, Dual 40 Series, Daily Driver



  4. #4
    Chief MarcInJapan's Avatar
    Join Date
    Mar 2009
    Location
    Syracuse, UT
    Posts
    34
    Thanks alot! It was 4 years of planning and 2 years of buying parts.

    622 HP/525 Torque On Pump Gas
    UnitedStangs.com
    MustangMafia.com

  5. #5
    Formerly 2011 GB/CS & CST 03 03 OW SVT's Avatar
    Join Date
    Sep 2006
    Location
    Fuwkawee
    Posts
    5,151
    Bad Ass Termy. Only two other CO's on this board.

    Welcome home! Thanks for your service
    17 Ram 1500 Big Horn Hemi
    16 Comp O GT Performance Pack
    03 Oxford white Cobra (Gone but not forgotten)

  6. #6
    No Traction due to Paxton PaxtonShelby's Avatar
    Join Date
    May 2007
    Location
    Moon Township
    Posts
    11,377
    Gorgeous cars!! Start a thread for the fox as well!
    2014 GT Premium - Sterling Gray Metallic - MT82 - Track Pack - Glass Roof - Recaro seats - Spoiler delete
    12.76 @ 114.04 bone stock. Koni yellow coil-overs, BMR watts, LCA and LCA relo brackets, Borla S-type axle back.

    1966 Coupe - 331 stroker - Bullet custom roller cam - cam and motor installed and dyno tuned by Rodeheavers Hot Rod - Astro A5 - McLeod RXT - 486 to the wheels - more fun than my little tires can handle

    1966 Oldsmobile Toronado - currently NOT on jackstands

  7. #7
    Chief MarcInJapan's Avatar
    Join Date
    Mar 2009
    Location
    Syracuse, UT
    Posts
    34
    Thanks guys! I appreciate the comments.

    The notch is my daughter's car. I have bought some things for it, but won't let her mod it until she gets a DD for college. I have on the shelf, T.body, Mass Air, and Lowering Springs. Hopefully this spring we will get those installed.

    622 HP/525 Torque On Pump Gas
    UnitedStangs.com
    MustangMafia.com

  8. #8
    Senior Member pop's stang's Avatar
    Join Date
    Dec 2008
    Location
    Belle Vernon, PA
    Posts
    854
    Wow Marc....you get around to all the sites just like I do! Good seeing you again. The car looks awesome!!!!
    Last edited by pop's stang; 12-24-2011 at 11:39 PM.
    "If speed wasn't important, it wouldn't be called the human race!"

  9. #9
    Chief MarcInJapan's Avatar
    Join Date
    Mar 2009
    Location
    Syracuse, UT
    Posts
    34
    Thanks! I was only visiting a couple of sites since I run my own 2 mustang forums. But, being back in the states has freed up some of my time so I am venturing out to other sites I used to visit in the past. I am a mustang forum junkie. :lol:

    622 HP/525 Torque On Pump Gas
    UnitedStangs.com
    MustangMafia.com

  10. #10
    Nothing clever to say.... jaa55's Avatar
    Join Date
    Sep 2007
    Location
    Dayton PA
    Posts
    3,795
    sick, i love comp orange
    03 Torch Red Anni. Ed. Cobra

    11 Grabber Blue 5.0, 3D500 spoiler, CS valance, GT premium, interior upgrade package, Brembos, MT-82 and Whipple powered SOLD

    01 cobra: traded

    93 LX Modular 4v swap
    Sean Hyland Motorsport forged rotating assembly, Teksid block, 01 cobra heads, cams and intake SOLD

  11. #11
    l3@l)&#l_#$$ AdamantiumSilvr's Avatar
    Join Date
    Dec 2008
    Location
    Natrona Heights PA
    Posts
    3,056
    Welcome back! Stangs are lookin niiiCe too! That shot w/ the mountains is awesome!
    Bu-2000-bash
    ALLSQUAD
    Steel City Muscle Cars
    CarCruises
    Flashlight Drags
    NMRA
    UMTR
    Modded Mustangs
    NHSCC

  12. #12
    Chief MarcInJapan's Avatar
    Join Date
    Mar 2009
    Location
    Syracuse, UT
    Posts
    34
    Thank you. Its one of those love or hate colors. Believe me when I tell you I have had people come up to me and say "its ugly" or "how could anyone drive a orange car". :lol:

    622 HP/525 Torque On Pump Gas
    UnitedStangs.com
    MustangMafia.com

  13. #13
    Formerly 2011 GB/CS & CST 03 03 OW SVT's Avatar
    Join Date
    Sep 2006
    Location
    Fuwkawee
    Posts
    5,151
    Some people have said that about my Grabber Blue.
    That's when I tell them that's why I'm paying/driving it and not them.
    17 Ram 1500 Big Horn Hemi
    16 Comp O GT Performance Pack
    03 Oxford white Cobra (Gone but not forgotten)

  14. #14
    1998 money pit
    Join Date
    Aug 2010
    Posts
    67
    beautiful car(s) thank you for your service
    it isn't ironic horsepower is measured in horses

  15. #15
    Kickin it Old School somethingclever's Avatar
    Join Date
    Aug 2006
    Location
    Bentleyville
    Posts
    4,625
    Looks good..how much boost and timing on pump?
    Last edited by somethingclever; 12-27-2011 at 01:05 PM.
    -JOHN

    Carburetors and SAE wrenches.................


    Buy Made in the USA - It Matters.

  16. #16
    JB 412mustangz's Avatar
    Join Date
    Apr 2009
    Location
    West Mifflin
    Posts
    1,247
    Looks real good!


    DD: 99 Civic Si

    Toys:
    07 GSXR 600

  17. #17
    The BOSS GOT SVT's Avatar
    Join Date
    Aug 2006
    Location
    Cranberry Twp PA
    Posts
    3,044
    hi marc

    it's been awhile

    i sold my car back in march of 2010, still owned by a member here though

    welcome back here
    Current Stable
    2013 School Bus Yellow Boss 302
    1993 Red Cobra

    Previous Stable
    2012 White Mustang-Traded
    2004 Competition Orange Terminator - Sold
    2003 Black Cobra-Traded
    1998 Black Cobra-Traded
    1991 White 5.0 Conv-Sold
    1986 Purple 5.0 Trunk-Sold to Psycho 5.0

    https://www.facebook.com/steelcitymusclecars

    https://www.facebook.com/cruisin.cranberry

  18. #18
    Chief MarcInJapan's Avatar
    Join Date
    Mar 2009
    Location
    Syracuse, UT
    Posts
    34
    Quote Originally Posted by somethingclever View Post
    Looks good..how much boost and timing on pump?
    622 HP on 17 lbs of boost...

    622 HP/525 Torque On Pump Gas
    UnitedStangs.com
    MustangMafia.com

  19. #19
    Kickin it Old School somethingclever's Avatar
    Join Date
    Aug 2006
    Location
    Bentleyville
    Posts
    4,625
    Quote Originally Posted by MarcInJapan View Post
    622 HP on 17 lbs of boost...
    Do you know max ignition timing on your 91 octane tune?
    -JOHN

    Carburetors and SAE wrenches.................


    Buy Made in the USA - It Matters.

  20. #20
    Senior Member Monkeygrits's Avatar
    Join Date
    Jul 2011
    Location
    Meyersdale, PA
    Posts
    1,101
    Beautiful!!!!

Similar Threads

  1. New Member, need some help!!
    By Nightmare99 in forum Welcome New Members
    Replies: 34
    Last Post: 02-15-2014, 07:01 PM
  2. New Member 97 Cobra
    By whitesnake in forum Welcome New Members
    Replies: 25
    Last Post: 09-21-2009, 11:47 PM
  3. Replies: 17
    Last Post: 09-04-2009, 03:05 PM
  4. New member, 94 svt cobra
    By 94svtcobra in forum Welcome New Members
    Replies: 23
    Last Post: 05-16-2008, 09:57 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •